May 16, 2025
rifleshooter.com

rifleshooter.com

Bill Marr's journal of shooting, reloading and gunsmithing

  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
What's new?
  • [ January 26, 2025 ] 782 Custom Gunworks “HUNDO” Loading Block Editorial
  • [ January 26, 2025 ] How do rifle suppressors affect muzzle velocity? Precision Rifles
  • [ May 31, 2023 ] The A-Team Mini-14? Customizing a Ruger Mini-14 A-Team
  • [ April 30, 2023 ] Removing stripped and sheared screws from a rifle Gunsmithing
  • [ February 28, 2023 ] Cut and Crown a Winchester 94 30-30 Gunsmithing
HomeRME installation

RME installation

Glock

Machining a Glock slide for a Trijicon RMR cut

July 30, 2015 Bill Marr 0

Allowing the shooter to only focus on one plane when shooting, red dot sights, long established on carbines, are gaining in popularity on pistols.  A Glock equipped with a Trijicon RMR red dot sight seems […]

Like us on Facebook!

Subscribe to rifleshooter.com via Email!

Never miss a post! Enter your email address to subscribe and receive notifications of new posts by email.

1911 Gunsmithing: lower and flare ejection port

1911 gunsmithing
March 15, 2017 0

Back bore a shotgun

Gunsmithing
August 5, 2015 0

Browning Citori spring and firing pin replacement

Gunsmithing
May 27, 2019 0

Customizing the 1911: machining a golf ball front strap

1911 gunsmithing
October 11, 2016 0

300 BLK accuracy problems? Maybe it isn’t you…

300 BLK
August 17, 2016 0
308 Winchester / 7.62x51mm NATO: Barrel Length versus Velocity (28" to 16.5")
6.5 Creedmoor- Effect of Barrel Length on Velocity: Cutting up a Creedmoor!
223 Remington/ 5.56mm NATO barrel length and velocity: 26 inches to 6 inches
223 Ackley Improved (223AI) loads and review: A better 223?
Ruger American Rifle Predator 223 Review
7.62x39 mm Russian: Effect of barrel length on muzzle velocity
M24 Sniper Rifle Review
Review: Remington 700 SPS Varmint
308 Winchester/ 7.62x51mm NATO Short barrel length and velocity- A six inch 308 bolt gun?
Budget precision rifle: Customizing the Savage Axis

Iron sight done right: Scalarworks PEAK sights

Daniel Defense M4 Upper Review

Modular Driven Technologies (MDT) Elite Sniper System (ESS) chassis initial impressions

Building a Custom Ruger American Rifle


 

 

 

 

 

Custom 1911 Project: Part 4- Machining a chain link front strap

September 12, 2016 0

Glue on recoil pad installation

November 23, 2019 0

Chambering a rifle barrel between centers

September 28, 2014 0

308 Winchester 175 Sierra MatchKing Ladder Test with Varget and IMR 4064

February 6, 2015 0

243 Winchester load development: 70 SMK, 95 TMK and 107 SMK

July 25, 2016 0

Building a custom Savage Model 10 in 6.5 Creedmoor

March 21, 2016 0

Jewell trigger installation on Winchester 70/FN Special Police

November 24, 2019 0

Remington Model Seven Actions are available!

November 21, 2014 0

Building (machining) an AR-15/M16 M4 barrel from a blank

May 13, 2014 0

Cerakote firearms finishing: Quick trick to coat screws

November 14, 2013 0

Posts

Pages
  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
  • Reviews
  • Rifles
  • Training
  • Optics
  • Hunting
  • Classic Rifleshooter.com
  • Bullet Selection
  • Cartridge Selection
  • Handguns
  • Contact us
  • Standards
  • Custom 870 Build
  • Project Guns- Gunsmithing articles and posts
  • Disclaimer
  • Rifles
  • Reviews
  • Gunsmithing
  • Tutorial
  • Accessories
  • Shotguns
  • New
  • Optics
  • Carbine Basics
  • Barrel Length and Velocity
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
Recent Posts
  • 782 Custom Gunworks “HUNDO” Loading Block
  • How do rifle suppressors affect muzzle velocity?
  • The A-Team Mini-14? Customizing a Ruger Mini-14
  • Removing stripped and sheared screws from a rifle
  • Cut and Crown a Winchester 94 30-30
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

All content Copyright 1998-2018 Rifleshooter.com, FTC disclosure: some links on this site are monetized

 

Loading Comments...
 

You must be logged in to post a comment.