March 14, 2026
rifleshooter.com

rifleshooter.com

Bill Marr's journal of shooting, reloading and gunsmithing

  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
What's new?
  • [ January 26, 2025 ] 782 Custom Gunworks “HUNDO” Loading Block Editorial
  • [ January 26, 2025 ] How do rifle suppressors affect muzzle velocity? Precision Rifles
  • [ May 31, 2023 ] The A-Team Mini-14? Customizing a Ruger Mini-14 A-Team
  • [ April 30, 2023 ] Removing stripped and sheared screws from a rifle Gunsmithing
  • [ February 28, 2023 ] Cut and Crown a Winchester 94 30-30 Gunsmithing
Homeshort barrel

short barrel

6.5 Creedmoor

6.5 Creedmoor Load Development: Short barrel (16.5″) suppressed and non-suppressed load development, 147 ELD and H4350

December 2, 2018 Bill Marr 0

I’ve written quite a bit about short barrelled precision rifles.  On this blog, I’ve built a variety of 308 Winchester, 223 Remington, 243 Winchester, 338 Lapua and 6.5 Creedmoor rifles with barrels in the 16-17 […]

Like us on Facebook!

Subscribe to rifleshooter.com via Email!

Never miss a post! Enter your email address to subscribe and receive notifications of new posts by email.

MDT ESS Folding Stock Review

Reviews
July 4, 2018 0

Remington Model 700 MAGPUL review

Precision Rifles
February 6, 2017 0

Geissele Super Dynamic Combat Trigger Review

Accessories
November 2, 2012 0

Closing screw holes on a shotgun receiver with a TIG welder

Gunsmithing
June 13, 2013 0

Review: Citadel RS-S1 Shotgun

Reviews
October 14, 2018 0
308 Winchester / 7.62x51mm NATO: Barrel Length versus Velocity (28" to 16.5")
223 Remington/ 5.56mm NATO barrel length and velocity: 26 inches to 6 inches
Colt M45A1 Review: USMC Pistol Review
6.5 Creedmoor- Effect of Barrel Length on Velocity: Cutting up a Creedmoor!
Review: Shooting the MAGPUL Ruger 10/22 Hunter X-22 Stock
M24 Sniper Rifle Review
308 Winchester/ 7.62x51mm NATO Short barrel length and velocity- A six inch 308 bolt gun?
223 Ackley Improved (223AI) loads and review: A better 223?
Review: Remington 700 SPS Varmint
Ruger American Rifle Predator 223 Review

Stripped screw removal (RMR from pistol)

6.5 Creedmoor load development: Reloder 17 and 140 gr. Sierra MatchKing (SMK) #1740

Custom 1911 Project: Part 4- Machining a chain link front strap

My bolt won’t close! Troubleshooting seized ejectors


 

 

 

 

 

Olongapo Outfitters AR-15 30 Round Grab & Go

July 15, 2011 0

MRAD or MOA scopes? Target size matters.

May 1, 2017 0

Smith and Wesson Revolver front sight insert replacement

February 19, 2019 0

MagnetoSpeed Chronograph Review

January 19, 2013 0

Sling swivel stud installation

September 9, 2018 0

Installing a bead on a shotgun barrel

February 7, 2019 0

Daewoo K2, DR-200/DR-300 barrel removal

March 23, 2019 0

Muzzle Brake Installation on a Precision Rifle: Timing and Installing an OPS R3E2C

December 1, 2013 0

Remington 870 Tritium Rifle Sight Installation

September 22, 2012 0

Smith and Wesson Revolver front sight insert replacement

February 19, 2019 0

Posts

Pages
  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
  • Reviews
  • Rifles
  • Training
  • Optics
  • Hunting
  • Classic Rifleshooter.com
  • Bullet Selection
  • Cartridge Selection
  • Handguns
  • Contact us
  • Standards
  • Custom 870 Build
  • Project Guns- Gunsmithing articles and posts
  • Disclaimer
  • Rifles
  • Reviews
  • Gunsmithing
  • Tutorial
  • Accessories
  • Shotguns
  • New
  • Optics
  • Carbine Basics
  • Barrel Length and Velocity
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
Recent Posts
  • 782 Custom Gunworks “HUNDO” Loading Block
  • How do rifle suppressors affect muzzle velocity?
  • The A-Team Mini-14? Customizing a Ruger Mini-14
  • Removing stripped and sheared screws from a rifle
  • Cut and Crown a Winchester 94 30-30
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

All content Copyright 1998-2018 Rifleshooter.com, FTC disclosure: some links on this site are monetized

 

Loading Comments...
 

You must be logged in to post a comment.