May 28, 2025
rifleshooter.com

rifleshooter.com

Bill Marr's journal of shooting, reloading and gunsmithing

  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
What's new?
  • [ January 26, 2025 ] 782 Custom Gunworks “HUNDO” Loading Block Editorial
  • [ January 26, 2025 ] How do rifle suppressors affect muzzle velocity? Precision Rifles
  • [ May 31, 2023 ] The A-Team Mini-14? Customizing a Ruger Mini-14 A-Team
  • [ April 30, 2023 ] Removing stripped and sheared screws from a rifle Gunsmithing
  • [ February 28, 2023 ] Cut and Crown a Winchester 94 30-30 Gunsmithing
Homeshotgun bead sight installation

shotgun bead sight installation

Gunsmithing

Mossberg 500: Cut, Crown and Choke Tube Installation

November 2, 2014 Bill Marr 0

The shotgun featured in this post is a beat up Mossberg 500 I purchased for $120.  It came with a 30″ barrel and a fixed full choke.  I’ll be converting it over to a home defense […]

Like us on Facebook!

Subscribe to rifleshooter.com via Email!

Never miss a post! Enter your email address to subscribe and receive notifications of new posts by email.

Building a custom Remington 700 hunting rifle

Gunsmithing
October 26, 2015 0

Starline 6.5 Creedmoor Brass Endurance Testing- firing the same cases 15 times

Precision Rifles
July 16, 2018 0

Shooting the New Jersey State Police Pistol Qualification HQC1

Pistols
October 12, 2015 0

Re-chambering a barrel: 243 Winchester to 6×47 Lapua

Gunsmithing
September 14, 2014 0

6.5 Creedmoor loads: 6.5 mm 150 gr. Sierra MatchKing (SMK)

6.5 Creedmoor
October 14, 2017 0
308 Winchester / 7.62x51mm NATO: Barrel Length versus Velocity (28" to 16.5")
223 Remington/ 5.56mm NATO barrel length and velocity: 26 inches to 6 inches
6.5 Creedmoor- Effect of Barrel Length on Velocity: Cutting up a Creedmoor!
223 Ackley Improved (223AI) loads and review: A better 223?
300 Winchester Magnum: How Does Barrel Length Change Velocity- A 16" 300 Win Mag?
M24 Sniper Rifle Review
308 Winchester/ 7.62x51mm NATO Short barrel length and velocity- A six inch 308 bolt gun?
6 Creedmoor barrel length versus muzzle velocity (31 to 17 inches)
Stripped screw removal (RMR from pistol)
338 Lapua Magnum: Barrel Length Versus Muzzle Velocity (30-17 inches)

243 Winchester- Effect of barrel length on velocity

AR15/M16 Bolt Radius Scraper Review

500 yards with a 223 Remington: Wood stock, solid pilot reamer and Shilen barrel…

Building a 300 Winchester Magnum Precision Rifle


 

 

 

 

 

CYBER MONDAY DEALS AT BROWNELLS!

November 28, 2016 0

USMC M40A5 Build- Part 3: Receiver Truing

June 13, 2015 0

Build a Remington 700 bolt disassembly tool

March 5, 2015 0

Shotgun Duckbill Review: Paradigm’s GATOR

July 9, 2017 0

Review: JTAC Thunder Chassis

May 6, 2017 0

1911 Gunsmithing: lower and flare ejection port

March 15, 2017 0

Cut and crown a shotgun barrel

April 30, 2020 0

Countouring a Rifle Barrel Blank

January 25, 2015 0

Badger Ordnance FTE Brake Installation

December 1, 2013 0

Installing a recoil pad on a fiberglass stock

January 30, 2017 0

Posts

Pages
  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
  • Reviews
  • Rifles
  • Training
  • Optics
  • Hunting
  • Classic Rifleshooter.com
  • Bullet Selection
  • Cartridge Selection
  • Handguns
  • Contact us
  • Standards
  • Custom 870 Build
  • Project Guns- Gunsmithing articles and posts
  • Disclaimer
  • Rifles
  • Reviews
  • Gunsmithing
  • Tutorial
  • Accessories
  • Shotguns
  • New
  • Optics
  • Carbine Basics
  • Barrel Length and Velocity
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
Recent Posts
  • 782 Custom Gunworks “HUNDO” Loading Block
  • How do rifle suppressors affect muzzle velocity?
  • The A-Team Mini-14? Customizing a Ruger Mini-14
  • Removing stripped and sheared screws from a rifle
  • Cut and Crown a Winchester 94 30-30
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

All content Copyright 1998-2018 Rifleshooter.com, FTC disclosure: some links on this site are monetized

 

Loading Comments...
 

You must be logged in to post a comment.