June 26, 2026
rifleshooter.com

rifleshooter.com

Bill Marr's journal of shooting, reloading and gunsmithing

  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
What's new?
  • [ January 26, 2025 ] 782 Custom Gunworks “HUNDO” Loading Block Editorial
  • [ January 26, 2025 ] How do rifle suppressors affect muzzle velocity? Precision Rifles
  • [ May 31, 2023 ] The A-Team Mini-14? Customizing a Ruger Mini-14 A-Team
  • [ April 30, 2023 ] Removing stripped and sheared screws from a rifle Gunsmithing
  • [ February 28, 2023 ] Cut and Crown a Winchester 94 30-30 Gunsmithing
Home2020July

Month: July 2020

Gunsmithing

Custom Cut Down Over and Under Shotgun

July 30, 2020 Bill Marr 0

I always wanted a cut down over and under shotgun. For the past two decades I’ve been looking for a suitable donor gun, but the relatively high cost of a quality used shotgun has kept […]

Like us on Facebook!

Subscribe to rifleshooter.com via Email!

Never miss a post! Enter your email address to subscribe and receive notifications of new posts by email.

Remington 700 SPS 243 Win to 6 Creedmoor conversion: Budget precision rifle

Gunsmithing
August 22, 2016 0

Bolt action rifle muzzle brake installation: Installing a Surefire MB762SSAL/RE

Accessories
May 27, 2013 0

Customizing the 1911: round butt Officer’s ACP conversion

1911 gunsmithing
November 1, 2016 0

Schmidt and Bender PMII LP MTC LT 5-25×56 review

Optics
August 4, 2017 0

6.5 Creedmoor 136 grain Scenar-L OTM Load Development, H4350

6.5 Creedmoor
August 1, 2015 0
6.5 Creedmoor- Effect of Barrel Length on Velocity: Cutting up a Creedmoor!
308 Winchester / 7.62x51mm NATO: Barrel Length versus Velocity (28" to 16.5")
223 Remington/ 5.56mm NATO barrel length and velocity: 26 inches to 6 inches
Budget precision rifle: Customizing the Savage Axis
Howa 1500 Review
IDF Modernized M24 SWS Review
Howa 1500 barreled action review: Howa 1500 versus Remington 700
M24 Sniper Rifle Review
Forster CO-AX reloading press: REVIEW- Is it the best press for precision rifle?
300 Winchester Magnum: How Does Barrel Length Change Velocity- A 16" 300 Win Mag?

Reloading for the Ruger Precision Rifle (RPR) 6.5 Creedmoor

Review: Ruger’s 10/22 Optic Ready Carbine

Modular Driven Technologies TAC21 Chassis System Review (Initial Thoughts)

Remington 870 Receiver Scratch Removal


 

 

 

 

 

Does primer size matter? 6.5 Creedmoor small v. large rifle primer brass comparisons

May 28, 2018 0

Mossberg Patriot Review

April 11, 2017 0

Review: TAC II Portable Two Position Wireless Turning Target System

June 24, 2011 0

Sierra Bullets releases 6.5 Creedmoor reloading data

January 9, 2017 0

Review: Mossberg MVP Patrol 5.56mm NATO (223 Remington) and 7.62 NATO (308 Winchester)

June 20, 2016 0

Remington 700 bolt handle void

December 13, 2017 0

Installing a short chambered barrel on a Remington 700

January 4, 2017 0

Glock firing pin channel removal and replacement

September 1, 2015 0

Skim bedding and pillar installation on a Remington 700

July 19, 2013 0

Rifle action stuck in bedding? Build a Remington 700 action puller

February 17, 2015 0

Posts

Pages
  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
  • Reviews
  • Rifles
  • Training
  • Optics
  • Hunting
  • Classic Rifleshooter.com
  • Bullet Selection
  • Cartridge Selection
  • Handguns
  • Contact us
  • Standards
  • Custom 870 Build
  • Project Guns- Gunsmithing articles and posts
  • Disclaimer
  • Rifles
  • Reviews
  • Gunsmithing
  • Tutorial
  • Accessories
  • Shotguns
  • New
  • Optics
  • Carbine Basics
  • Barrel Length and Velocity
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
Recent Posts
  • 782 Custom Gunworks “HUNDO” Loading Block
  • How do rifle suppressors affect muzzle velocity?
  • The A-Team Mini-14? Customizing a Ruger Mini-14
  • Removing stripped and sheared screws from a rifle
  • Cut and Crown a Winchester 94 30-30
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

All content Copyright 1998-2018 Rifleshooter.com, FTC disclosure: some links on this site are monetized