October 4, 2023
rifleshooter.com

rifleshooter.com

Bill Marr's journal of shooting, reloading and gunsmithing

  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
What's new?
  • [ May 31, 2023 ] The A-Team Mini-14? Customizing a Ruger Mini-14 A-Team
  • [ April 30, 2023 ] Removing stripped and sheared screws from a rifle Gunsmithing
  • [ February 28, 2023 ] Cut and Crown a Winchester 94 30-30 Gunsmithing
  • [ January 8, 2023 ] IDF Modernized M24 SWS Review 308 Winchester
  • [ November 26, 2022 ] M24 Accuracy with M80 Ball Ammunition? 308 Winchester
Homecustom over and under

custom over and under

Gunsmithing

Custom Cut Down Over and Under Shotgun

July 30, 2020 Bill Marr 0

I always wanted a cut down over and under shotgun. For the past two decades I’ve been looking for a suitable donor gun, but the relatively high cost of a quality used shotgun has kept […]

Like us on Facebook!

Subscribe to rifleshooter.com via Email!

Never miss a post! Enter your email address to subscribe and receive notifications of new posts by email.

AR15 Upper Receiver Build

Gunsmithing
September 11, 2011 0

AK Bolton Gas Block Installation

Gunsmithing
February 9, 2013 0

Custom Left-Hand Remington 700 in 308 Winchester Precision Rifle

Precision Rifles
August 3, 2015 0

Review: Grayboe Renegade stock

Precision Rifles
July 27, 2017 0

6.5 Creedmoor loads: 123 SMK and 130 TMK with VARGET

6.5 Creedmoor
August 20, 2017 0
223 Remington/ 5.56mm NATO barrel length and velocity: 26 inches to 6 inches
6.5 Creedmoor- Effect of Barrel Length on Velocity: Cutting up a Creedmoor!
308 Winchester / 7.62x51mm NATO: Barrel Length versus Velocity (28" to 16.5")
Budget precision rifle: Customizing the Savage Axis
6.5 Creedmoor- Effects of Barrel Length on Velocity 2019
7.62x39 mm Russian: Effect of barrel length on muzzle velocity
Remington 700 ADL Review
223 Ackley Improved (223AI) loads and review: A better 223?
308 Winchester/ 7.62x51mm NATO Short barrel length and velocity- A six inch 308 bolt gun?
Building a Custom Ruger American Rifle

The A-Team Mini-14? Customizing a Ruger Mini-14

Cut and crown a rifle barrel without a lathe (11 degree target crown)

Custom Remington 870 Wingmaster Build

Removing a stuck pull-through cleaning kit


 

 

 

 

 

Beretta M9 Pistol Review- My 20 years with the M9

July 5, 2015 0

Replacing a plastic recoil pad on a shotgun

August 31, 2022 0

Customizing the 1911: detail work, golf ball reverse plug

December 16, 2017 0

MDT Ckye-Pod Review

January 27, 2019 0

Factory 6.5 Creedmoor Ammunition Accuracy

November 28, 2019 0

Marlin 336 Straight Stock Conversion

November 18, 2012 0

Ruger 10/22 accuracy upgrade: Shortening factory chamber to improve accuracy

November 30, 2015 0

Tactical Operations bolt knob installation on a Remington 700

March 14, 2017 0

Rebarrel a Remington 700 without a lathe: McGowen’s Remage barrel conversion

March 7, 2015 0

Customizing a Savage B.Mag Target Rifle

February 7, 2022 0

Posts

Pages
  • Contact us
  • Disclaimer
  • Project Guns- Gunsmithing articles and posts
  • Reviews
  • Rifles
  • Training
  • Optics
  • Hunting
  • Classic Rifleshooter.com
  • Bullet Selection
  • Cartridge Selection
  • Handguns
  • Contact us
  • Standards
  • Custom 870 Build
  • Project Guns- Gunsmithing articles and posts
  • Disclaimer
  • Rifles
  • Reviews
  • Gunsmithing
  • Tutorial
  • Accessories
  • Shotguns
  • New
  • Optics
  • Carbine Basics
  • Barrel Length and Velocity
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
Recent Posts
  • The A-Team Mini-14? Customizing a Ruger Mini-14
  • Removing stripped and sheared screws from a rifle
  • Cut and Crown a Winchester 94 30-30
  • IDF Modernized M24 SWS Review
  • M24 Accuracy with M80 Ball Ammunition?
Meta
  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

All content Copyright 1998-2018 Rifleshooter.com, FTC disclosure: some links on this site are monetized